Coil Zippers, Metal Zippers, Plastic Zippers

Reinforcing film sealing unit for open-end 6 and 8 mm. zippers

OER/*

Description

For metal, coil, and plastic molded zippers.
This unit is designed for sealing the plastic reinforcing film to the tape: this operation is required, before attaching pin and box, to the open-end zippers.
It is composed of the sealing unit and the EWT panel, responsible for the power supply and the temperature control.
The reinforcing film is coated with a hot-melt resin that melts at a temperature lower than that to which the film itself melts.
This unit is therefore required to press the film against the zipper tape, and, at the same time, to bring the hot-melt resin to the melting temperature.
The result of this operation is a reinforcing film perfectly fixed on the zipper tape, thanks to the melting, on the latter, of hot-melt resin.
The duration of this pressing action, and its value, can be partly decided by the operator to obtain a good compromise between an optimal application of reinforcement and acceptable production rates.
The reinforcing film is applied only on the front side of the open-end zipper (the side where there is the puller of the slider), and for this reason, it is twice as thick as those normally used for application on both sides (0.28 mm.).
Once the application of reinforcing film is done, and before applying pin and box for obtaining a open-end zipper, three more steps are needed:
1) Removal of the reinforcing film between the two cords of the zipper tape: by hand or by the OEL tool.
2) Cutting the reinforced part of the zipper tape to the right measure for the insertion of pin and box: by hand or by the OET tool.
3) Lateral trimming of the excess of the reinforcing film: only manually

Each of these three operations can be easily accomplished through the use of good sharp scissors. For the second operation, however, we offer a specific tool that will facilitate the operations and make more consistent quality results.

The unit has no parts subject to wear.

Variants

OER/6: for 6 mm. zippers.
OER/8: for 8 mm. zippers.

Items

OER/*: Mechanical unit for attaching the reinforcement film to 6 and 8 mm open-end zippers
EWT: Electric panel for controlling the OER / unit..

Spare parts

n.d.

Details

Press for attaching the film:
dimensions: (p x l x h): 19 x 11 x 37,5 cm
weight: approx 7,3 kg
Electric panel EWT:
dimensions: (p x l x h):
weight:  approx kg

Info

    (richiesto)

    Contatto commerciale
    Desideri essere contattato da un nostro consulente?
    (richiesto)

    Iscrizione alla newsletter
    Desideri ricevere informazioni aggiornate e offerte speciali via email?
    (facoltativo)

    Coil Zippers, Metal Zippers, Plastic Zippers

    Reinforcing film sealing unit for open-end 6 and 8 mm. zippers

    OER/*

    Details

    Press for attaching the film:
    dimensions: (p x l x h): 19 x 11 x 37,5 cm
    weight: approx 7,3 kg
    Electric panel EWT:
    dimensions: (p x l x h):
    weight:  approx kg
    Info

      (richiesto)

      Contatto commerciale
      Desideri essere contattato da un nostro consulente?
      (richiesto)

      Iscrizione alla newsletter
      Desideri ricevere informazioni aggiornate e offerte speciali via email?
      (facoltativo)

      Description

      For metal, coil, and plastic molded zippers.
      This unit is designed for sealing the plastic reinforcing film to the tape: this operation is required, before attaching pin and box, to the open-end zippers.
      It is composed of the sealing unit and the EWT panel, responsible for the power supply and the temperature control.
      The reinforcing film is coated with a hot-melt resin that melts at a temperature lower than that to which the film itself melts.
      This unit is therefore required to press the film against the zipper tape, and, at the same time, to bring the hot-melt resin to the melting temperature.
      The result of this operation is a reinforcing film perfectly fixed on the zipper tape, thanks to the melting, on the latter, of hot-melt resin.
      The duration of this pressing action, and its value, can be partly decided by the operator to obtain a good compromise between an optimal application of reinforcement and acceptable production rates.
      The reinforcing film is applied only on the front side of the open-end zipper (the side where there is the puller of the slider), and for this reason, it is twice as thick as those normally used for application on both sides (0.28 mm.).
      Once the application of reinforcing film is done, and before applying pin and box for obtaining a open-end zipper, three more steps are needed:
      1) Removal of the reinforcing film between the two cords of the zipper tape: by hand or by the OEL tool.
      2) Cutting the reinforced part of the zipper tape to the right measure for the insertion of pin and box: by hand or by the OET tool.
      3) Lateral trimming of the excess of the reinforcing film: only manually

      Each of these three operations can be easily accomplished through the use of good sharp scissors. For the second operation, however, we offer a specific tool that will facilitate the operations and make more consistent quality results.

      The unit has no parts subject to wear.

      Variants

      OER/6: for 6 mm. zippers.
      OER/8: for 8 mm. zippers.

      Items

      OER/*: Mechanical unit for attaching the reinforcement film to 6 and 8 mm open-end zippers
      EWT: Electric panel for controlling the OER / unit..

      Spare parts

      n.d.